A Disassemble the mounting assembly, as it has been shipped,
by turning the sink flange until the projections align with the
notches in the mount ring and allow you to pull the sink flange
up and out of the remaining mount assembly. Note the
sequence of these parts as they are stacked and refer to A
and B to identify each part. Unpack the 3 mount screws and
screw them half way through the mount ring (notice “THIS
SIDE UP” is imprinted on top of the mount ring). Next, stack
the rubber gasket on top of the protector ring and sit them on
top of the pointed ends of the mount screws.
B Keep these assembled parts together and set aside. Before
you connect the disposer to the mount assembly under the
sink, you may want to practice engaging the groove of the
cushion ring to the ridge at the bottom of the sink flange
(see A and read Sec. 5).
C Be sure your sink is clean. Pack the underside rim of the sink
flange with plumber’s putty (see C). Position the sink flange so
it is centered and readable as you look into your sink. Push the
sink flange firmly into the sink opening to make a good seal.
DO NOT move or rotate the sink flange once seated or the seal
may be broken.
D Take the remaining portion of the mount assembly, as it was
set aside and make sure that the rubber gasket is on top of the
protector ring. From under the sink, while holding the sink
flange firmly with one hand, line up the notches in the mount
ring with the projections of the sink flange. Slide the mount
assembly up onto the sink flange, past the projections and
give the mount assembly a 1/4 turn, so that it will hang by
itself (see D).
E Tighten the 3 mounting screws evenly with a screwdriver
(see E). DO NOT OVERTIGHTEN! Trim off excess putty.
2a. INSTALLATION OF 3-BOLT MOUNTING ASSEMBLY
For TP-50, TP-75 and TP-125 models. Read completely before starting
NB - Pay close attention to the order of mount assembly parts,
as they have been correctly assembled by the factory.
(See A and B.)
metsyS tnuoM tloB-3
PROTECTOR RING
SINK MOUNT RING
MOUNTING SCREWS (3)
SINK FLANGE
SINK FLANGE GASKET
STOPPER*
SINK FLANGE**
SINK
HOPPER
ELBOW
GASKET
SCREWS
SERIAL #- RECORD ON
WARRANTY CARD
MOUNTING
SCREWS**
SCREW
CLAMP**
PROJECTIONS
RIDGE
RIDGE
DISCHARGE
ELBOW
ELBOW
FLANGE
DISHWASHER
DISCHARGE INLET
CUSHION RING**
RUBBER SINK
FLANGE GASKET**
PROTECTOR RING**
MOUNT RING**
PLUMBER’S
PUTTY
END BELL
(ELECTRICAL
CONNECTIONS)
3E
3D
3C
MOUNTING
SCREWS
PROTECTOR
RING
RUBBER
GASKET
SINK
FLANGE
CUSHION RING
3B
SCREW
CLAMP
MOUNTING
RING
Mount Assembly
* Batch Feed Stopper looks different than the stopper illustrated.
** Mount Assembly (see 2B)
3A
STOPPER*
SINK FLANGE**
SINK
HOPPER
ELBOW
GASKET
SCREWS
SERIAL #- RECORD ON
WARRANTY CARD
MOUNTING
SCREWS**
SCREW
CLAMP**
PROJECTIONS
RIDGE
RIDGE
DISCHARGE
ELBOW
ELBOW
FLANGE
DISHWASHER
DISCHARGE INLET
CUSHION RING**
RUBBER SINK
FLANGE GASKET**
PROTECTOR RING**
MOUNT RING**
PLUMBER’S
PUTTY
END BELL
(ELECTRICAL
CONNECTIONS)
3E
3D
3C
MOUNTING
SCREWS
PROTECTOR
RING
RUBBER
GASKET
SINK
FLANGE
CUSHION RING
SCREW
CLAMP
MOUNTING
RING
Mount Assembly
* Batch Feed Stopper looks different than the stopper illustrated.
** Mount Assembly (see 2B)
B
3A
STOPPER*
SINK FLANGE**
SINK
HOPPER
ELBOW
GASKET
SCREWS
SERIAL #- RECORD ON
WARRANTY CARD
MOUNTING
SCREWS**
SCREW
CLAMP**
PROJECTIONS
RIDGE
RIDGE
DISCHARGE
ELBOW
ELBOW
FLANGE
DISHWASHER
DISCHARGE INLET
CUSHION RING**
RUBBER SINK
FLANGE GASKET**
PROTECTOR RING**
MOUNT RING**
PLUMBER’S
PUTTY
END BELL
(ELECTRICAL
CONNECTIONS)
3E
3D
3C
MOUNTING
SCREWS
PROTECTOR
RING
RUBBER
GASKET
SINK
FLANGE
CUSHION RING
3B
SCREW
CLAMP
MOUNTING
RING
Mount Assembly
* Batch Feed Stopper looks different than the stopper illustrated.
** Mount Assembly (see 2B)
C D E
A
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern